How to turn on your gas appliance
Many of our customers wonder about the procedure to follow in order to start up their gas stove or fireplace. This is why our experts at the Boutique Foyer will show you the procedure to follow in order not to forget any step!
1) First of all, it is important to check that the gas tank is at least 20% full, otherwise there will not be enough gas to start your appliance. Most tanks have an indicator for this.
2) Make sure that the valve near your device (or inside) is in the open position, that is, positioned parallel to the gas line. To do this, turn the valve counterclockwise.
3) Check that the thermostat and the “on / off / pilot” button are both turned off or in the “off” position. Now you need to light the pilot (also known as the “pilot light”).
4) Gently push in the "on / off / pilot" button and turn it counterclockwise until it is in the "pilot" position. While holding this button down, repeatedly press the ignition button (indicated by a lightning bolt symbol) to cause sparks to ignite the pilot.
Note: You may have to repeat this step several times before the pilot light stays on. It is important to keep the "on / off / pilot" button pressed for no more than 15 seconds at a time. Between each test, wait at least 30 seconds before starting again.
5) When the pilot stays on by itself, keep the button pressed for about 30 seconds, then release.
6) Lightly press the "on / off / pilot" button again, then turn counterclockwise to the "on" position and turn on the thermostat (it could take 1 to 2 minutes after switching on the pilot before the thermostat turns on).
We recommend that you run your gas stove or fireplace once every 30 days to eliminate ignition problems in the fall. In addition, your appliance should be checked by a gas company once every three years.
Source: Propane 2000
Masonry cleaners to the rescue
DETERGENTS for new masonry
NMD-80
The NMD-80 is the most efficient, profitable and safe way to clean new masonry. A very powerful detergent-based solution designed for efficient and safe cleaning of efflorescence and excess mortar on the surface, such as bricks, stones, colored blocks, synthetic stones, prestressed and granite.
Cleans without brushing, low pressure application, high pressure rinsing.
Available in 1 gal., 5 gal. and 55 gal. US.
EF-FORTLESS
A soapy solution that melts the powdery bloom and helps
control the return. The user does not have to use a pressure washer to get a good result. This product contains very mild acids and can be used on color sensitive surfaces and will not discolor brick, stone or mortar. A rinse is enough to remove everything.
Covers more or less 75 ft per gallon.
Available in 5 gal. US
Catering products
Restoration Products
ONE-RESTORE
Innovative product for cleaning and maintaining the exterior surfaces of
buildings such as limestone, concrete, brick, glass and windows. Safe and efficient. Does not affect anodized aluminum and does not scratch the glass.
Easy to apply. Spray and rinse, no brushing necessary.
Removes stains caused by weather, pollution, mold and oxidation.
No harm to the skin, little odor.
Available in 5 gal. and 55 gal. US
GSR (Glazed Surface Restoration)
GRS is a very effective detergent without hydrofluoric acid originally
developed to clean glossy brick and terra cotta.
Apply and rinse, cleans brick, concrete and glass.
Do not let the product dry on the surface, rinse thoroughly.
Available in 5 gal. US
For more information on these cleaners see:
4 tips for storing your firewood
Our experts present their 4 simple tips to properly store your firewood and ensure that it stays dry:
1) To facilitate drying, we recommend that you split logs 3 inches and more in diameter;
2) Even commercial firewood is not always split small enough, so it may be useful to split it before stacking it: this will make it easier to dry the logs and feed the fire;
3) Stack the wood in separate rows and out in the open, where the summer sun can warm it and the breeze can rid it of moisture. It is best not to store wet wood in a shed or shed, as it will take much longer to dry;
4) The top of the stack can be covered to protect it from the rain, but leave the sides uncovered so that air can circulate and dry the logs.
Is my wood dry enough?
Usually wood that is cut, split and stack tightly in early spring will be ready for fall. Dense woods like maple or ash, especially large logs, will take longer to dry. A simple way to tell if your wood is dry enough to burn is to split a log: if the center is wet, the wood still needs some time to dry.
